WoodsBuggy.com https://www.woodsbuggy.com/phpBB3/ |
|
kingpin Q https://www.woodsbuggy.com/phpBB3/viewtopic.php?f=4&t=14656 |
Page 1 of 1 |
Author: | jesse [ Mon Jan 14, 2013 2:48 am ] |
Post subject: | kingpin Q |
i put my frontend all together lastnight it is my first time using k/p and i wanted to keep my 4 lug weels so i bought the conversion berrings all went together and work well but the spindle had this spacer on it or i believe thats what it is do i have this together correct the red arrow points to the spacer i was talking about |
Author: | buggybarn [ Mon Jan 14, 2013 4:30 am ] |
Post subject: | Re: kingpin Q |
It looks like an old bearing |
Author: | NRIbuggys [ Mon Jan 14, 2013 10:39 am ] |
Post subject: | Re: kingpin Q |
That looks like the inside of an old bearing. I think it should come off |
Author: | MadMike [ Mon Jan 14, 2013 12:23 pm ] |
Post subject: | Re: kingpin Q |
X 2 |
Author: | 2800passat [ Mon Jan 14, 2013 1:34 pm ] |
Post subject: | Re: kingpin Q |
put a propane torch on it.hi jesse. |
Author: | buggybarn [ Mon Jan 14, 2013 2:00 pm ] |
Post subject: | Re: kingpin Q |
Oops sorry jesse brain fart they are right I was thinking of differ spacer sorry guys thanks for correcting me. |
Author: | jesse [ Mon Jan 14, 2013 10:37 pm ] |
Post subject: | Re: kingpin Q |
well is their a spacer that should be on their cause theirs no way to tighten it all down if it was all the way back |
Author: | kvw [ Mon Jan 14, 2013 11:09 pm ] |
Post subject: | Re: kingpin Q |
Yes there should be a spacer, but the spacer is narrower than the ball bearing race in your picture. I can measure a spacer tomorrow night if you need. Good Luck Kenric |
Author: | jesse [ Mon Jan 14, 2013 11:47 pm ] |
Post subject: | Re: kingpin Q |
Ok thanks I thiught it looked off lol |
Author: | buggybarn [ Tue Jan 15, 2013 1:37 am ] |
Post subject: | Re: kingpin Q |
lol so I was right ? Lol I thought there was.kvw will get u set straight . That does look like an old bearing race though |
Author: | jesse [ Tue Jan 15, 2013 2:11 am ] |
Post subject: | Re: kingpin Q |
yea i thought the same cause the groove around it but it had something else left in front of that so i figured that was the old race never built a front end what a hastle it has been lol |
Author: | buggybarn [ Tue Jan 15, 2013 2:22 am ] |
Post subject: | Re: kingpin Q |
I can go out to shop and look and let u know |
Author: | buggybarn [ Tue Jan 15, 2013 3:04 am ] |
Post subject: | Re: kingpin Q |
Confirmed yes there is a spacer it measures .564 width . outside diameter is 1.61 and it has a single groove on outside. I don't know how to post pics on forum but ill post it on buggy builds. I thought there was a spacer been awhile since had one apart lol. |
Author: | jesse [ Tue Jan 15, 2013 3:59 am ] |
Post subject: | Re: kingpin Q |
ok then if it has a groove this one is right it has a groove |
Author: | buggybarn [ Tue Jan 15, 2013 4:05 am ] |
Post subject: | Re: kingpin Q |
Did u see pics? |
Author: | jesse [ Tue Jan 15, 2013 4:48 am ] |
Post subject: | Re: kingpin Q |
yes i did looks like i have it correct thanks again for the help |
Author: | reno2165 [ Tue Jan 15, 2013 5:58 am ] |
Post subject: | Re: kingpin Q |
ok, now that you FINALLY got it figured out jesse... paint that sh!t |
Author: | jesse [ Tue Jan 15, 2013 6:52 am ] |
Post subject: | Re: kingpin Q |
Lol I dont plan to leave it like that just wsnted to be possitive I have it right I still need to play with the shims so I will paint then |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |