i would think that all you had to do is swap out the bearings for the kingpin spindle bearings, i dont think the wheels are any different just the bearings
| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| Aluminum Balljoint spindle mount rims http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=7&t=9955 |
Page 1 of 1 |
| Author: | nitro_mudder [ Sun Jul 25, 2010 4:59 pm ] |
| Post subject: | Aluminum Balljoint spindle mount rims |
I have no spindles that these will fit. Looking to sell or trade them for King pin ones. |
|
| Author: | ridenrace6 [ Mon Jul 26, 2010 12:45 am ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
i would think that all you had to do is swap out the bearings for the kingpin spindle bearings, i dont think the wheels are any different just the bearings
|
|
| Author: | nitro_mudder [ Mon Jul 26, 2010 10:29 am ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
Well if anyone knows the conversion bearings that would be great. |
|
| Author: | ridenrace6 [ Mon Jul 26, 2010 11:10 am ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
if im not mistaken the bearings my buddy ordered for his spindle mounts were 52mm O.D. so maybe if you can check and see what the O.D. is on what you got then you tell that way if the bearings will interchange |
|
| Author: | nitro_mudder [ Mon Jul 26, 2010 11:24 am ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
Inners and outers are different on the balljoint ones. |
|
| Author: | ridenrace6 [ Mon Jul 26, 2010 12:55 pm ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
i knew the inner and outer I.D. of the bearings were different but thought that O.D. was the same on all spindle mount bearings |
|
| Author: | chris38375 [ Mon Jul 26, 2010 2:28 pm ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
i do think u can find bearings for it,i seen them somewhere in a magazine |
|
| Author: | woogiebugger1 [ Wed Jul 28, 2010 3:30 pm ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
The conversion bearings you are looking for are available, However, the reliability factor + the cost = sell them and buy kp wheels. You'll be further ahead. JMO |
|
| Author: | nitro_mudder [ Wed Jul 28, 2010 5:09 pm ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
Thanks, that was the original plan. Just need them when I go to the dunes a few times a year. |
|
| Author: | Bob-o [ Fri Jul 30, 2010 10:40 pm ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
go to donssport.com. you may need to call them but they have the convertion bearings you need to put ball joint wheels on a king pin spindle. |
|
| Author: | nitro_mudder [ Sat Jul 31, 2010 11:24 am ] |
| Post subject: | Re: Aluminum Balljoint spindle mount rims |
Called him up this morning. $45 + tax & Shipping. Not bad. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|