did'nt you say it had a swing axel in it
if so, weld some irs piviots in shortin the spring plates and your ready to go. Swingaxels had soft tortion bars if I remember right
| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| wanted bus http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=7&t=5796 |
Page 1 of 1 |
| Author: | windrock child [ Fri Feb 13, 2009 6:15 pm ] |
| Post subject: | wanted bus |
I am looking for a bus torison and a bus transmission and axles everthing to switch from swingaxle.in the in the east tn area peferabley thanks. |
|
| Author: | Kyle [ Fri Feb 13, 2009 6:21 pm ] |
| Post subject: | Re: wanted bus |
run a car torsion. much softer. |
|
| Author: | rockrockets1 [ Fri Feb 13, 2009 6:40 pm ] |
| Post subject: | Re: wanted bus |
by all means use a car torsion |
|
| Author: | bradley59dzl [ Fri Feb 13, 2009 7:08 pm ] |
| Post subject: | Re: wanted bus |
but if u want i can hook u up with bus torsion 6 rib and axles 650.00 straight out of the bus... |
|
| Author: | windrock child [ Fri Feb 13, 2009 7:25 pm ] |
| Post subject: | Re: wanted bus |
so what i really need is just a irs car torsion will the bus axles bolt right up to that. I have a old irs car torsion i guess i just need trans and axles thanks guys |
|
| Author: | rockrockets1 [ Fri Feb 13, 2009 7:42 pm ] |
| Post subject: | Re: wanted bus |
did'nt you say it had a swing axel in it if so, weld some irs piviots in shortin the spring plates and your ready to go. Swingaxels had soft tortion bars if I remember right
|
|
| Author: | windrock child [ Fri Feb 13, 2009 7:53 pm ] |
| Post subject: | Re: wanted bus |
how much do i need to shorten them and do i just weld the pivots right on to the torsion itself. prob sounds dumb to u all this is my first rodeo with a rail dont know alot bout them thanks |
|
| Author: | rockrockets1 [ Fri Feb 13, 2009 7:59 pm ] |
| Post subject: | Re: wanted bus |
you can get pockets at any buggy shop Tim Deaton prob has them at Southern buggys they set against the frame horns where the trany sets you can also get a bug to bus conversion kit from him and get trailing arms from our CEO D.Marks then you set if it were me I would go with 3x3 |
|
| Author: | bradley59dzl [ Fri Feb 13, 2009 8:29 pm ] |
| Post subject: | Re: wanted bus |
[quote="bradley59dzl"]but if u want i can hook u up with bus torsion 6 rib and axles 650.00 straight out of the bus...[/quote] if you need a torsion i have one with dbl spring plates boxed trln arms with newer disc brakes |
|
| Author: | windrock child [ Fri Feb 13, 2009 10:08 pm ] |
| Post subject: | Re: wanted bus |
how much do you want for it and excatly were are you located? |
|
| Author: | bradley59dzl [ Sat Feb 14, 2009 10:59 am ] |
| Post subject: | Re: wanted bus |
windrock child wrote: how much do you want for it and excatly were are you located? if u buy it with a trans an axles take 900 for everything 271 petersburg rd enon valley pa 16120 right on pa ohio line |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|