| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| Mike's Machine & Fabrication For Sale List http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=7&t=15970 |
Page 4 of 4 |
| Author: | MadMike [ Fri May 15, 2015 11:51 am ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
I make 3"drop combo spindles. If your asking if I use a stock size link/pin spindle stub, no. I do not make micro stub rear arms, I make something I think is even better. |
|
| Author: | MadMike [ Wed May 27, 2015 11:43 am ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
I've ordered a fresh batch of material, front or rear arms anyone? |
|
| Author: | MadMike [ Thu Jun 11, 2015 5:28 pm ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
Out with the old and in with the new(er). My old 4X7" band saw starting acting like a *itch so it became time to replace it. I've got no complaints with it, 33 years of cutting steel, time to retire it.  New(er) saw will do 8X12, see if it can last 30 years, made in the USA, I guess we'll see. 
|
|
| Author: | Cush53 [ Fri Jun 12, 2015 7:02 am ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
Very nice Sent from my XT1080 using Tapatalk |
|
| Author: | aboone993 [ Fri Jun 12, 2015 9:54 am ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
This day in time its almost impossible to buy quality parts . But that is not a problem with Mike's parts ! They are top notch. Usps lost my shipments from him twice but mike made it right and would not except a dime extra for his trouble. Hard to find people like that anymore. THANKS Sent from my LGL31L using Tapatalk |
|
| Author: | MadMike [ Fri Jun 12, 2015 4:10 pm ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
aboone993 wrote: This day in time its almost impossible to buy quality parts . But that is not a problem with Mike's parts ! They are top notch. Usps lost my shipments from him twice but mike made it right and would not except a dime extra for his trouble. Hard to find people like that anymore. THANKS Your welcome. I couldn't see this ending any other way, you paid your bill and it wasn't your fault the union protected government slackers decided to "loose" your parts. The second no show is clearly my fault, knowing that doing something over and over again expecting a different result is the classic definition of stupidity. So I must of had a senior moment or a brain tumor or something trying twice, won't happen again  .
|
|
| Author: | blackbeauty [ Wed Jun 17, 2015 9:01 pm ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
Could it be possible to build a set of stock width x2.5 longer rear trailing arms Just that guy |
|
| Author: | MadMike [ Wed Jun 17, 2015 10:20 pm ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
blackbeauty wrote: Could it be possible to build a set of stock width x2.5 longer rear trailing arms Just that guy Yes I can. Not to long ago I built a set of stock width, 3" longer for a guy that had a wider than stock torsion housing. |
|
| Author: | blackbeauty [ Thu Jun 18, 2015 4:58 am ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
Ok that's basically where I'm at are the prices still the same as on the store Just that guy |
|
| Author: | MadMike [ Thu Jun 18, 2015 11:01 am ] |
| Post subject: | Re: Mike's Machine & Fabrication For Sale List |
That's correct. |
|
| Page 4 of 4 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|