WoodsBuggy.com
http://www.woodsbuggy.com/phpBB3/

WTB Used CNC Pedel Assembly
http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=7&t=15353		 Page 1 of 1
Author:  dirtdobber [ Mon May 06, 2013 10:55 am ]
Post subject:  WTB Used CNC Pedel Assembly
I just need clutch and brake, ive got a gas pedel.
Author:  snail rail [ Tue May 07, 2013 5:16 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
good luck finding a used set. Hope you have better luck than what I've had trying to locate some reasonably priced. Still haven't found any used ones other than a few priced within a few dollars of a complete new assembly. Appletree had a sale a week or so ago that was 10% off orders online, but last day was april 30
Author:  snail rail [ Tue May 07, 2013 6:05 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
Here ya go, theres a set complete with slave cyl. Like I said, I wish I would have just went ahead and bit the bullet and ordered some thru appletree that last week of April. shipping on orders over $75 is free combined with the 10% off sale they were running at the time, a set of CNC's without gas pedal (if I remember correctly),including slave cyl ended up being $253....Cheaper than everywhere else I've found. Well let me correct myself, have actually found complete CNC hyd pedal assemblies cheaper on a few sites, until you figure in their crazy ass shipping rates....one site I looked at calculated the shipping a few dollars shy of $50....$50 TO SHIP A HYDRAULIC PEDAL ASSEMBLY???? :roll:

http://www.thesamba.com/vw/classifieds/ ... id=1437606
Author:  MadMike [ Tue May 07, 2013 7:40 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
All my pedal stuff is Wilwood. From Summit they are CHEAPER then CNC so why would you want to buy someone else's problems.
Author:  snail rail [ Tue May 07, 2013 10:08 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
Hey Madmike is your clutch slave cyl wilwood also? Does your setup have the brake/clutch master cyl together (like the CNC assembly in link above)??
Author:  snail rail [ Tue May 07, 2013 10:33 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
Hey dirt dobber, I know you said you're looking for both the pedal & clutch assembly, not sure what kind of brake master cyl you're already using but this wilwood single clutch pedal assembly looks like a real nice setup if a man was just needing the hydraulic clutch. Hell it has floor mount pedal, 3/4" bore master with slave cylinder also. It's tempted to go this route since my brakes already work fine, but guess I'll wait till I can scrape up the funds for complete setup

http://cgi.ebay.com/ws/eBayISAPI.dll?Vi ... ink:top:en
Author:  MadMike [ Tue May 07, 2013 10:40 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
snail rail wrote:
Hey Madmike is your clutch slave cyl wilwood also? Does your setup have the brake/clutch master cyl together (like the CNC assembly in link above)??

The slave cylinder is Wilwood and no they are separate peddles.
Image
Author:  dirtdobber [ Wed May 08, 2013 1:36 am ]
Post subject:  Re: WTB Used CNC Pedel Assembly
Thanks for input guys, I go by the summit place in Georgia every week, I'll stop in and look next week at wildwood stuff.
Author:  dirtdobber [ Wed May 08, 2013 8:39 am ]
Post subject:  Re: WTB Used CNC Pedel Assembly
Madmike you wouldn't know part number for that setup at summit, would you. No problem if you don't
Author:  hpfreak [ Wed May 08, 2013 8:48 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
I used this for my clutch. works great.

http://www.jegs.com/i/Wilwood/950/340-1469/10002/-1?parentProductId=
Author:  MadMike [ Wed May 08, 2013 10:24 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
The Wilwood pedal assembly with a 3/4" master cylinder is part# CMB-14-0008 costs $112.93
Wilwood slave cylinder is part# WIL-260-1333 costs $73.95
And I didn't see this before but
Howe Racing slave cylinder part# HRE-829 costs $45.97
So for $158.90 you can get a Wilwood pedal assembly and a Howe slave cylinder.
For $271.83 you get 2 Wilwood pedals and a Howe slave cylinder and get 10 times the product CNC could ever be.
Author:  snail rail [ Wed May 08, 2013 10:40 pm ]
Post subject:  Re: WTB Used CNC Pedel Assembly
hpfreak wrote:
I used this for my clutch. works great.

http://www.jegs.com/i/Wilwood/950/340-1469/10002/-1?parentProductId=

I was looking at that same assembly yesterday and looks like hell of a setup. I want a hyd clutch so bad....but think I'm gonna buy some v tread front tires first.... damn priorities.... :roll:
Author:  dirtdobber [ Thu May 09, 2013 10:44 am ]
Post subject:  Re: WTB Used CNC Pedel Assembly
Thanks mike, sorry bout your arm,
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/