make sure you buy there pressure plate because some of the stock one are not compatitable. save your self the headach if your going that way.
| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| WTB parts http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=7&t=10097 |
Page 1 of 1 |
| Author: | volksdude2010 [ Wed Aug 18, 2010 3:43 am ] |
| Post subject: | WTB parts |
i am looking to buy a set of 2x3 trailing arm with bus stub axles or just either of the two seprate i am need a possibly needing a bell housing to bolt up to a six rib and a subaru motor my brother volksdude07 said that there is such a thing im not sure where i could find one or if some one has one for sale for a reasonable price any input on that or selling anything or could possibly trade vw parts for them? |
|
| Author: | Stevo [ Wed Aug 18, 2010 7:27 am ] |
| Post subject: | Re: WTB parts |
Check out Bigscotts build he got one, http://www.woodsbuggy.com/index.php?opt ... 47&start=0 |
|
| Author: | Stevo [ Wed Aug 18, 2010 7:35 am ] |
| Post subject: | Re: WTB parts |
Heres one on ebay, probly the way Id go http://cgi.ebay.com/ebaymotors/Subaru-V ... ccessories |
|
| Author: | davehix [ Wed Aug 18, 2010 5:22 pm ] |
| Post subject: | Re: WTB parts |
make sure you buy there pressure plate because some of the stock one are not compatitable. save your self the headach if your going that way.
|
|
| Author: | john [ Wed Aug 18, 2010 6:00 pm ] |
| Post subject: | Re: WTB parts |
sawyer! makes very nice 2x3 trailing arm's!!! |
|
| Author: | Stevo [ Wed Aug 18, 2010 6:08 pm ] |
| Post subject: | Re: WTB parts |
davehix wrote: make sure you buy there pressure plate because some of the stock one are not compatitable. save your self the headach if your going that way. it works with the stock 2.2 or 2.5 clutch not the wrx clutch. The wrx clutch is a pull release and the other is push |
|
| Author: | davehix [ Wed Aug 18, 2010 9:38 pm ] |
| Post subject: | Re: WTB parts |
you have to measure the center hole of pressure plate. we had this problem with the one we did and it took a few rides befor it tore it up. this is the email that i got after i sent pics to him. "The release bearing slipped through the pressure plate fingers causing it to over travel. This happen because center between the fingers is too wide in diameter. If you compare the Valeo pressure to OEM, the OEM center is smaller in diameter. " Best regards, Mao Online Sales Manager Small Car Performance 4720 South Tacoma Way Tacoma , WA 98409 |
|
| Author: | volksdude2010 [ Thu Aug 19, 2010 12:27 am ] |
| Post subject: | Re: WTB parts |
ok i see how it goes thx alot that gives me some options i got all winter to make this right and dont wanna have to do things a secound time now this might be a stupid question but with that bell housing for the bus tranny to the subaru can you use the stock hydralic pedal off a subaru on it or what kind of clutch would work? |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|