| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| frame welding http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=4&t=5868 |
Page 1 of 1 |
| Author: | charlie [ Sat Feb 21, 2009 11:20 pm ] |
| Post subject: | frame welding |
I can find no one in northern ohio that will weld new tube on my buggy for liabilaty reasons. does everyone have this prob. and does anyone know where i can get this done in my area? im just not comfortable doing it my self. I want the front hoop of my roll bar and the tube that my steering shaft bolts to replaced. |
|
| Author: | MadMike [ Sat Feb 21, 2009 11:59 pm ] |
| Post subject: | Re: frame welding |
There are a couple of guys up your way who might offer their services. I would do it for ya, except I'm a little far away. If you run out of options send me a PM. |
|
| Author: | rockrockets1 [ Sun Feb 22, 2009 9:08 am ] |
| Post subject: | Re: frame welding |
Same here ,if you down this way I would be happy to help |
|
| Author: | plumberbill [ Sun Feb 22, 2009 11:29 am ] |
| Post subject: | Re: frame welding |
is it prepped and ready to be welded or are you looking for someone to do this for you |
|
| Author: | jayrod [ Sun Feb 22, 2009 10:17 pm ] |
| Post subject: | Re: frame welding |
Id say bring it on over, when I get mine done by my gf's dad, But Im about an hour from you |
|
| Author: | charlie [ Sun Feb 22, 2009 10:28 pm ] |
| Post subject: | Re: frame welding |
plumberbill wrote: is it prepped and ready to be welded or are you looking for someone to do this for you no the old needs cut out and new bent and installed. i have the tools to remove but i didnt think it was a good idea till some one looked at it. so i knew what to cut and were. i would rather pay you to do all of it i will help but im no welder nor do i have the experance needed |
|
| Author: | afterburnt [ Mon Feb 23, 2009 8:07 pm ] |
| Post subject: | Re: frame welding |
try ED's WELDING the number is 419-433-4101. hes over in heron over by the vermillion river. hes a race chassis fab shop. I've used him to bend some tubing once. that was about 8 years ago. i think hes still there. I have bending dies for 1 5/8" tubing, what size are you using? if it is a quick one day job, i could help out, I have a small fab shop over in brookpark about 3 minutes from the airport. |
|
| Author: | charlie [ Mon Feb 23, 2009 9:08 pm ] |
| Post subject: | Re: frame welding |
afterburnt wrote: try ED's WELDING the number is 419-433-4101. hes over in heron over by the vermillion river. hes a race chassis fab shop. I've used him to bend some tubing once. that was about 8 years ago. i think hes still there. I have bending dies for 1 5/8" tubing, what size are you using? if it is a quick one day job, i could help out, I have a small fab shop over in brookpark about 3 minutes from the airport. ill give him a call if not i hope you or plumber bill can do it i think it can be done in one day but i dont know. i think its 1 1/2 pipe. |
|
| Author: | plumberbill [ Sun Mar 01, 2009 11:18 am ] |
| Post subject: | Re: frame welding |
sorry didnt get back to ya sooner lost track of this post. do you have any pics to give me an idea of what you want to do |
|
| Author: | charlie [ Sun Mar 01, 2009 12:26 pm ] |
| Post subject: | Re: frame welding |
plumberbill wrote: sorry didnt get back to ya sooner lost track of this post. do you have any pics to give me an idea of what you want to do ill take som picks pm me with email i have a hard time posting pics. |
|
| Author: | plumberbill [ Sun Mar 01, 2009 12:29 pm ] |
| Post subject: | Re: frame welding |
charlie wrote: plumberbill wrote: sorry didnt get back to ya sooner lost track of this post. do you have any pics to give me an idea of what you want to do ill take som picks pm me with email i have a hard time posting pics. setup a photobucket account its free |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|