| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| how do you static time a motor. http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=3&t=16316 |
Page 1 of 1 |
| Author: | motoxkfx [ Tue Nov 12, 2013 11:22 pm ] |
| Post subject: | how do you static time a motor. |
Ok i have a 2110 and i am running MSD 6AL digital and a pro billet distributor. i am not sure how i would go about setting static time. I need to do this because i got a new set of carbs and messed with the timing for no good reason when i took the old ones off  dumbass me!!!!now i can not seem to get the motor to idle long enough to set my best lean idle. |
|
| Author: | bige70chevy [ Wed Nov 13, 2013 12:14 am ] |
| Post subject: | Re: how do you static time a motor. |
im pretty sure msd has a help hotline...if you dont get the answer you need here |
|
| Author: | 2800passat [ Wed Nov 13, 2013 1:03 am ] |
| Post subject: | Re: how do you static time a motor. |
Point rotor at #1 wire. Point 7.5 btdc at case seam. loosen dist. connect 1 wire type test lite to neg side of coil and stick test lite into a spring on the carb for a ground. Turn key on. Rotate dist cw til lite goes out then counter cw til lite turns on. tighten dist. Remove wrench from pulley. If you have a 2 wire test lite then connect them to the coil. Red + black neg . Stick the test lite in the spring. Rotate dist the same way but instead the lite will go from green to bright green with a 2 wire test lite. |
|
| Author: | motoxkfx [ Thu Nov 14, 2013 9:52 am ] |
| Post subject: | Re: how do you static time a motor. |
Ok i got it running last night its back to being a ripper again. Now for the next question where the hell do you mount the return spring on these carbs on my old set there was a piece that hung down that had a hole in it to mount the spring but these are cast and do not have a place to put it. both sides of the carbs look the same.  This is what my old set looked like this set did not come with this. 
|
|
| Author: | diamonddav [ Thu Nov 14, 2013 10:57 am ] |
| Post subject: | Re: how do you static time a motor. |
I just noticed your little red arrow8-) never considered that,nor tried it, and dont know if id trust it not to break that brass piece!! Darrell has his screwed to the frame with different springs.seems to work. I think the correct answer is riggernig it:roll::grin::D:-D Posted using the WoodsBuggy Mobile App |
|
| Author: | Rick [ Thu Nov 14, 2013 11:45 am ] |
| Post subject: | Re: how do you static time a motor. |
I made some small aluminum brackets thats held down by the mounting stud Attachment: ImageUploadedByWoodsBuggy1384443912.247866.jpg [ 20.87 KiB | Viewed 2980 times ] Posted using the WoodsBuggy Mobile App |
|
| Author: | jeff69 [ Thu Nov 14, 2013 11:51 am ] |
| Post subject: | Re: how do you static time a motor. |
I just ran a spring from the hex bar where the throttle cable hooks up to my exhaust pipe where the spring go on the collector good luck Posted using the WoodsBuggy Mobile App iPhone |
|
| Author: | hillaholic [ Fri Nov 15, 2013 11:26 pm ] |
| Post subject: | Re: how do you static time a motor. |
motoxkfx wrote: Ok i got it running last night its back to being a ripper again. Now for the next question where the hell do you mount the return spring on these carbs on my old set there was a piece that hung down that had a hole in it to mount the spring but these are cast and do not have a place to put it. both sides of the carbs look the same. This is what my old set looked like this set did not come with this. I just hooked the spring to the bottom filter mount. Posted using the WoodsBuggy Mobile App |
|
| Author: | davehix [ Sat Nov 16, 2013 10:39 am ] |
| Post subject: | Re: how do you static time a motor. |
I did something like Rick did . Works good |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|