WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
King Pin to ball joint conversion bearings http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=29&t=11831 |
Page 1 of 1 |
Author: | Pugh [ Sat Jun 04, 2011 4:55 pm ] |
Post subject: | King Pin to ball joint conversion bearings |
Has anyone used these 17-2795 & 17-2796 conversion bearing to run ball joint rotors on king/link pin spindles? Just about every online vendor sells them. Does anyone know what these cross reference too in Timken ? |
Author: | ridenrace6 [ Sun Jun 05, 2011 1:38 am ] |
Post subject: | Re: King Pin to ball joint conversion bearings |
i think these are the ones you talking about? http://www.kustom1warehouse.net/Combo_s ... age298.htm if so i would order 1 inner($10) and 1 outer($8) and then take them to the local parts house that sells timken and see if they can match them up and use the ordered $18 set as a spare jmo. |
Author: | ridenrace6 [ Wed Jul 18, 2012 2:23 am ] |
Post subject: | Re: King Pin to ball joint conversion bearings |
has anybody actually done this conversion? i been looking into this again with no luck at the local parts house (if it even deserves the name) but it seems that even appletree and kustom 1 cant even agree on what the O.D. is supposed to be, and after looking at socal it seems they say something about a differentouter end on kp spindles and only using a special conv rotor so now im even confused on what to get http://www.appletreeauto.com/VW-BRAKE-S ... and-SEALS/ http://www.kustom1warehouse.net/Combo_a ... 3-2011.htm http://www.socalautoparts.com/wheel-bea ... _1550.html |
Author: | Cush53 [ Wed Jul 18, 2012 7:03 am ] |
Post subject: | Re: King Pin to ball joint conversion bearings |
I had ordered the ones from socal, and they didn't work and they were just balljoint bearing they sent me and argued with me on the phone about it. I even went to bearings incorperated to look for some and they have every timkin know to man and they couldn't match anything up. |
Author: | Rick [ Wed Jul 18, 2012 10:28 am ] |
Post subject: | Re: King Pin to ball joint conversion bearings |
I'm a carquest jobber and we sell federal mogul/bca bearings witch use timken numbers. Ive tried to come up with bearings to put ball joint rotor on king pin stub with no avail the are odd ball bearing |
Author: | dirtdobber [ Thu Jul 19, 2012 5:48 pm ] |
Post subject: | Re: King Pin to ball joint conversion bearings |
I've used the empi conversion kit ( link pin spindle to balljoint hub ) for years. I've had good luck with mine. But that is about the only thing I like about empi. IMO |
Author: | apintonut [ Tue Feb 18, 2014 7:16 am ] |
Post subject: | Re: King Pin to ball joint conversion bearings |
Ok i ran up against this on my own to no avail Trying to run my cheap ball joint disk brake set up (u may know 92 & 93 vw jetta rear disk or cut down drums (75-93 vw rear drums) and 88-91 honda civic disk brake) Ended up that i had a set of boat hubs laying around 4x100 and some honda civic brakes that did fit |
Author: | MadMike [ Tue Feb 18, 2014 1:25 pm ] |
Post subject: | Re: King Pin to ball joint conversion bearings |
The ones I use to make required you to machine the rotor to except bigger bearings. The bearing #'s Inner Timken# 30205M 9\KMI outer SKF# 32004 X/Q |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |