Here are some pictures of my spindles that I am upgrading on my single-seater, it is a 2.5" drop spindle.
| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| Spindle upgrade http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=26&t=8639 |
Page 1 of 1 |
| Author: | pipedope [ Fri Feb 05, 2010 2:32 pm ] |
| Post subject: | Spindle upgrade |
Here are some pictures of my spindles that I am upgrading on my single-seater, it is a 2.5" drop spindle.
|
|
| Author: | Odyknuck [ Fri Feb 05, 2010 4:24 pm ] |
| Post subject: | Re: Spindle upgrade |
Nice job. I like the way you used the old stub as a locater and support. |
|
| Author: | JeffClay [ Fri Feb 05, 2010 4:27 pm ] |
| Post subject: | Re: Spindle upgrade |
god those look soooooooooooooooo heavy! hahaha j.k. awesome brian! |
|
| Author: | nitro_mudder [ Fri Feb 05, 2010 6:20 pm ] |
| Post subject: | Re: Spindle upgrade |
The reason for these come from the D&K trip? Mine did, lol. |
|
| Author: | HippyCrack [ Tue Aug 10, 2010 11:01 pm ] |
| Post subject: | Re: Spindle upgrade |
color me new, but why "drop" spindles on a buggy? Is it a street car? OR is there something I don't understand here? |
|
| Author: | Maddog [ Wed Aug 11, 2010 12:09 am ] |
| Post subject: | Re: Spindle upgrade |
The spindles are dropped [repositioned lower than their original location] thus raising the front axle or beam. |
|
| Author: | kybuggy1 [ Wed Aug 11, 2010 12:23 pm ] |
| Post subject: | Re: Spindle upgrade |
Yeah, we all call them "drop" spindles , but they should be called "dropped" spindles, referring to the location of the spindle on the knuckle. Drop spindles are what street guys use to lower stuff. |
|
| Author: | hyde [ Wed Aug 11, 2010 5:49 pm ] |
| Post subject: | Re: Spindle upgrade |
Nice |
|
| Author: | Tyrus [ Tue Sep 14, 2010 8:43 pm ] |
| Post subject: | Re: Spindle upgrade |
Very nice like to have a set.... |
|
| Author: | instigator [ Wed Sep 15, 2010 3:06 pm ] |
| Post subject: | Re: Spindle upgrade |
if there is enough interest? i will start making the plates. |
|
| Author: | A. Cole [ Wed Sep 15, 2010 4:38 pm ] |
| Post subject: | Re: Spindle upgrade |
Its nice you don't have to hack-up 2 sets of spindles for those. With a little modes you could use it for K/P too. Nice! |
|
| Author: | instigator [ Wed Sep 15, 2010 4:45 pm ] |
| Post subject: | Re: Spindle upgrade |
thats the plan any way. just gonna use the bj spud for both bj and kp plates |
|
| Author: | A. Cole [ Wed Sep 15, 2010 9:09 pm ] |
| Post subject: | Re: Spindle upgrade |
instigator wrote: thats the plan any way. just gonna use the bj spud for both bj and kp plates Are you gonna make a plate with a bend for K/P spindle/beam? |
|
| Author: | Tyrus [ Wed Sep 15, 2010 10:18 pm ] |
| Post subject: | Re: Spindle upgrade |
instigator wrote: if there is enough interest? i will start making the plates. how much for a set? |
|
| Author: | volksdude2007 [ Wed Sep 22, 2010 9:51 pm ] |
| Post subject: | Re: Spindle upgrade |
instigator if you plan on making these plates if there is enough interest in them let me know i would buy a set from ya for ball joint front beam by the way pipedope awsome job maybe you should make a little money on the side also and sell some of your skill 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|