It is currently Thu Mar 28, 2024 5:55 pm

Board index » Tech and Fab » Parts Fabrication

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Bending U bend header
PostPosted: Tue May 06, 2014 7:37 am 
Offline
User avatar

Joined: Mon Mar 08, 2010 2:29 pm
Posts: 214
Location: cortland, Ohio
How can I put a 90° bend to the right on this header after the down bend without destroy the finish? Is it possible? Any ideas?

Sent from my DROID RAZR HD using Tapatalk

_________________
Dont' be be scared. When it dought floor it!


Top
 Profile  
 
PostPosted: Tue May 06, 2014 7:38 am 
Offline
User avatar

Joined: Mon Mar 08, 2010 2:29 pm
Posts: 214
Location: cortland, Ohio
Image

Sent from my DROID RAZR HD using Tapatalk

_________________
Dont' be be scared. When it dought floor it!


Top
 Profile  
 
PostPosted: Tue May 06, 2014 11:58 am 
Offline
BOTM Winner
User avatar

Joined: Wed Nov 07, 2007 2:07 pm
Posts: 1599
Location: Petersburg, Ky
if you buy the right shoe, and it doesnt kink, i bet it would sill scratch it up

_________________
Maybe you should chug on over to mamby pamby land....


Top
 Profile  
 
PostPosted: Tue May 06, 2014 1:03 pm 
Offline
Master fabricator
User avatar

Joined: Fri Mar 02, 2007 11:55 pm
Posts: 2304
Location: S.W. Pa. Wellsville Water Cooled Chapter
Don't think there is enough tubing there to bend a 90 even if the finish wasn't important.

_________________
Of all the things I've lost, I miss my mind the most.
M
A
G
A


Top
 Profile  
 
PostPosted: Tue May 06, 2014 5:28 pm 
Offline
BOTM winner/Master fabricator
User avatar

Joined: Tue Jan 01, 2008 10:26 pm
Posts: 910
Location: brookpark ohio ---- wellsville
Just go to the part store and get a chrome tailpipe tip and put it on , it will let the exhaust blow behind you, not down, and it looks great too,

Image


Top
 Profile  
 
PostPosted: Wed May 07, 2014 7:32 am 
Offline
BOTM Winner
User avatar

Joined: Wed Nov 07, 2007 2:07 pm
Posts: 1599
Location: Petersburg, Ky
Image

_________________
Maybe you should chug on over to mamby pamby land....


Top
 Profile  
 
PostPosted: Wed May 07, 2014 9:27 am 
Offline
User avatar

Joined: Mon Mar 08, 2010 2:29 pm
Posts: 214
Location: cortland, Ohio
When I put it on the side like it should be it hits the frame. :x I will have to make the u-bend tighter. Then i probably could use one of those tips!! I also have a slip on super trap I want to be able to use when I go Road Dogging!! :twisted:

_________________
Dont' be be scared. When it dought floor it!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

Board index » Tech and Fab » Parts Fabrication

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group