well guess they all answered all ready lol x5
| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| Advice on running wires through chassis http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=18&t=15051 |
Page 1 of 1 |
| Author: | taterbug [ Thu Mar 14, 2013 12:26 am ] |
| Post subject: | Advice on running wires through chassis |
Like the title says does anybody have any advice for running wires through chassis tubes |
|
| Author: | Andrew_Ha [ Thu Mar 14, 2013 2:28 am ] |
| Post subject: | Re: Advice on running wires through chassis |
Don't do it weakens the frame by drilling holes lets water in makes rust faster jmo |
|
| Author: | holeman [ Thu Mar 14, 2013 9:50 am ] |
| Post subject: | Re: Advice on running wires through chassis |
x2 |
|
| Author: | RaceBugg1098 [ Thu Mar 14, 2013 10:25 am ] |
| Post subject: | Re: Advice on running wires through chassis |
dont do it! |
|
| Author: | davehix [ Thu Mar 14, 2013 1:18 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
well guess they all answered all ready lol x5
|
|
| Author: | giveitagallon [ Thu Mar 14, 2013 1:34 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
X6 |
|
| Author: | MickeyMouse [ Thu Mar 14, 2013 2:07 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
X7 X8 X9 and X10... I thought it would look cool to not see the wires... Worst decision I ever made. The bars rusted from the inside and I could never cut or weld on the frame because I did not want to hurt the wires. |
|
| Author: | Red Barron [ Thu Mar 14, 2013 4:23 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
I have three wire in my frame tubing and two holes for the head lights. But that is it. |
|
| Author: | hpfreak [ Thu Mar 14, 2013 7:50 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
id say no dont drill holes in the frame but if you feel you must I found a good way to do it is drill the holes. blow air in one hole and feed in some kite string. the air blowing out the other hole tends to blow the kite string out. then use the kite string to pull the wires through. |
|
| Author: | taterbug [ Thu Mar 14, 2013 10:26 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
I was just gonna do head lights and tail lights and silicone all the holes afterwards |
|
| Author: | MadMike [ Thu Mar 14, 2013 10:53 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
In case someone forget to mention, Don't do it.  
|
|
| Author: | hpfreak [ Thu Mar 14, 2013 11:41 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
survey says......... DONT DO IT |
|
| Author: | rip-it [ Fri Mar 15, 2013 6:50 am ] |
| Post subject: | Re: Advice on running wires through chassis |
I saw someone weld brake lines to the frame and ran the wires through them. Looked clean and I believe there was a post on it in this site somewhere?? Just a thought. 
|
|
| Author: | kendel [ Fri Mar 15, 2013 4:15 pm ] |
| Post subject: | Re: Advice on running wires through chassis |
Do it! But not in the frame tubes! In the wire tubes you tack to the frame to run them through i do this on trailers ect to protect the wires, but never drill hole in the frame to run wires |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|