| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| subaru adapter question http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=17&t=10946 |
Page 1 of 1 |
| Author: | volksdude2007 [ Sat Jan 01, 2011 2:33 pm ] |
| Post subject: | subaru adapter question |
i am getting ready to order a adapter kit as soon as i found out what i am asking about ive got a 94 subaru legacy 2.2 i am wanting to hook up to a 6 rib nose cone shift tranny my question is what would this be, a subarru to type 1 transmission or what 
|
|
| Author: | Firebug [ Sat Jan 01, 2011 3:44 pm ] |
| Post subject: | Re: subaru adapter question |
volksdude2007 wrote: i am getting ready to order a adapter kit as soon as i found out what i am asking about ive got a 94 subaru legacy 2.2 i am wanting to hook up to a 6 rib nose cone shift tranny my question is what would this be, a subarru to type 1 transmission or what Just tell them what you are running,,,the bell housings have the same bolt pattern for type 1, 2, and 091 (6rib) |
|
| Author: | volksdude2007 [ Sat Jan 01, 2011 4:53 pm ] |
| Post subject: | Re: subaru adapter question |
ok thank you |
|
| Author: | bmoore [ Sat Jan 01, 2011 10:18 pm ] |
| Post subject: | Re: subaru adapter question |
kennedy will take care of you! and they dont mind takeing the time to answer any question you may have 
|
|
| Author: | volksdude2007 [ Thu Jan 06, 2011 6:40 pm ] |
| Post subject: | Re: subaru adapter question |
ok here is another question 200mm or 225mm bore what should i get, here is what i plan on running clutch wise a stock clutch with a stage 2 pressure plate motor will be bolted to a 6 rib transmission which of these would you suggest for what i will be using as described k.a.p asked this question to me and i was not sure |
|
| Author: | Maddog [ Thu Jan 06, 2011 7:19 pm ] |
| Post subject: | Re: subaru adapter question |
The 225 will be a stronger clutch setup, but will also weigh more. I'd probably go with the 200 because of that in a buggy. The heavier clutch&flywheel assembly will make the engine rev slower and will be harder on the tranny if you drop the clutch. |
|
| Author: | passat2800 [ Thu Jan 06, 2011 8:03 pm ] |
| Post subject: | Re: subaru adapter question |
 
|
|
| Author: | bmoore [ Thu Jan 06, 2011 8:08 pm ] |
| Post subject: | Re: subaru adapter question |
passat2800 wrote: :idea: are you jehovah witness 
|
|
| Author: | RaceBugg1098 [ Fri Jan 07, 2011 12:34 pm ] |
| Post subject: | Re: subaru adapter question |
the 200mm would be cheaper in the long run too! |
|
| Author: | volksdude2007 [ Sun Jan 09, 2011 11:23 pm ] |
| Post subject: | Re: subaru adapter question |
thanks we ordered the 200mm now just have a 2 1/2 week wait for some reason all is good though still gives us a few months to do it |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|