| WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
| What size master cylinder. .. http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=10&t=16771 |
Page 1 of 1 |
| Author: | klu408 [ Mon Mar 17, 2014 12:51 am ] |
| Post subject: | What size master cylinder. .. |
I have wilwood dynalite calipers and there 4 piston... I have a 3/4 master cylinder and cut brakes now with a residual valve. But my pedal is spongy and brakes suck.. I've bled and bled and nothing helps and have been told mc needs to be bigger? Any opinions? Sent from my SCH-I605 using Tapatalk |
|
| Author: | buggiejunky [ Mon Mar 17, 2014 9:32 am ] |
| Post subject: | Re: What size master cylinder. .. |
Ur system still has air in it Make sure ur bleeders r straight up when ur bleeding it Maybe try to make a power bleeder http://www.ebay.com/itm/Motive-Products ... c1&vxp=mtr |
|
| Author: | 2800passat [ Mon Mar 17, 2014 10:30 am ] |
| Post subject: | Re: What size master cylinder. .. |
1ST OF ALL ...WEAR LATEX GLOVES. bRAKE FLUID ABSORBS THRU YER SKIN AND GOES INTO YER BLOOD. 2ND. YEARS AGO I HAD BRAKES THAT JUST WOULD NOT BLEED OUT. I PUT A "T" IN THE BRAKE LINE SOMEWHERE AROUND THE TRAILING ARM PIVOT BOLT . 1 RUBBER BRAKE LINE WENT VERTICALLY UP WITH A CAP ON IT. THAT T WOULD CATCH EVERY MIGRATING AIR BUBBLE AS I DROVE. 30 MINUTES LATER I REMOVED THE CAP AND THE BRAKE FLUID WAS A FEW INCHES DOWN AND I WOULD POUR FRESH FLUID IN THE HOSE AND CAP IT. 3RD OLD FROZEN CALIPERS WITH RUSTED PISTONS WILL NOT BLEED OUT. 4TH A BENT STUB AXLE, WARPED ROTOR, OR BAD WHEEL BEARINGS WILL MOVE PADS OUT AND WHEN YOU GO TO APPLY BRAKES THEY GO TO THE FLOOR. A PULSING PEDAL MEANS A WARPED ROTOR OR STUB AXLE. AND AS ALWAYS PART # 66599 WHEEL CYL REPAIR KIT FOR $3.99 AT AUTOZONE HAS THE EXACT RUBBER CUPS FOR A 3/4 FOOT BRAKE OR CLUTCH. CALL 1ST BECAUSE THEY ALWAYS HAVE TO ORDER THEM. EASY TO REMEMBER BECAUSE IT READS UPSIDE DOWN ASWELL. AND QUIT CROSSING RIVERS OR LETTING YOUR BRAKES SIT OUT IN THE RAIN. WHEEL BEARRINGS, BRAKE PISTONS, MASTER CYLINDERS, NICE SEATS AND A/C MOTORS HATE WATER. WATER BUBBLES IN ALUMINIUM CYLINDER BORES MAKE PITS. |
|
| Author: | 2800passat [ Mon Mar 17, 2014 10:31 am ] |
| Post subject: | Re: What size master cylinder. .. |
1ST OF ALL ...WEAR LATEX GLOVES. BRAKE FLUID ABSORBS THRU YER SKIN AND GOES INTO YER BLOOD. 2ND. YEARS AGO I HAD BRAKES THAT JUST WOULD NOT BLEED OUT. I PUT A "T" IN THE BRAKE LINE SOMEWHERE AROUND THE TRAILING ARM PIVOT BOLT . 1 RUBBER BRAKE LINE WENT VERTICALLY UP WITH A CAP ON IT. THAT T WOULD CATCH EVERY MIGRATING AIR BUBBLE AS I DROVE. 30 MINUTES LATER I REMOVED THE CAP AND THE BRAKE FLUID WAS A FEW INCHES DOWN AND I WOULD POUR FRESH FLUID IN THE HOSE AND CAP IT. 3RD OLD FROZEN CALIPERS WITH RUSTED PISTONS WILL NOT BLEED OUT. 4TH A BENT STUB AXLE, WARPED ROTOR, OR BAD WHEEL BEARINGS WILL MOVE PADS OUT AND WHEN YOU GO TO APPLY BRAKES THEY GO TO THE FLOOR. A PULSING PEDAL MEANS A WARPED ROTOR OR STUB AXLE. AND AS ALWAYS PART # 66599 WHEEL CYL REPAIR KIT FOR $3.99 AT AUTOZONE HAS THE EXACT RUBBER CUPS FOR A 3/4 FOOT BRAKE OR CLUTCH. CALL 1ST BECAUSE THEY ALWAYS HAVE TO ORDER THEM. EASY TO REMEMBER BECAUSE IT READS UPSIDE DOWN ASWELL. AND QUIT CROSSING RIVERS OR LETTING YOUR BRAKES SIT OUT IN THE RAIN. WHEEL BEARRINGS, BRAKE PISTONS, MASTER CYLINDERS, NICE SEATS AND A/C MOTORS HATE WATER. WATER BUBBLES IN ALUMINIUM CYLINDER BORES MAKE PITS. |
|
| Author: | klu408 [ Mon Mar 17, 2014 10:47 am ] |
| Post subject: | Re: What size master cylinder. .. |
I guess those same 3/4 cups will fit turning brakes too? Sent from my SCH-I605 using Tapatalk |
|
| Author: | jeff69 [ Mon Mar 17, 2014 10:35 pm ] |
| Post subject: | Re: What size master cylinder. .. |
I had the same problem with mine I put 4 piston calipers off a Mercedes on it but still suck at stopping so I put a 1 inch wilwood master cyclinder it made a world of different I'm still trying to get all the air out but still a big improvement Sent from my iPhone using Tapatalk |
|
| Author: | 2800passat [ Mon Mar 17, 2014 10:44 pm ] |
| Post subject: | Re: What size master cylinder. .. |
neg klu... the cut brakes have a cup more like a seal than a cup. Basicly it has a hole in it like a Lifesaver candy.. Some Auto zone dude let me browse thru 200 packages years ago. |
|
| Author: | klu408 [ Mon Mar 17, 2014 11:07 pm ] |
| Post subject: | Re: What size master cylinder. .. |
Well i rebuilt master and calipers new brake lines... and bled more... still spongy pedal.. gonna order 1" bore tomorrow. Thanks for the part numbers DD you saved me some cash... Sent from my SCH-I605 using Tapatalk |
|
| Author: | hpfreak [ Tue Mar 18, 2014 11:53 am ] |
| Post subject: | Re: What size master cylinder. .. |
IF YOU HAVE DRUMS ON THE FRONT MAKE SURE THEIR ADJUSTED REALLY WELL. |
|
| Author: | klu408 [ Tue Mar 18, 2014 6:00 pm ] |
| Post subject: | Re: What size master cylinder. .. |
All I have is rear disk Sent from my SCH-I605 using Tapatalk |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|