WoodsBuggy.com http://www.woodsbuggy.com/phpBB3/ |
|
Heim joint tie rods http://www.woodsbuggy.com/phpBB3/viewtopic.php?f=10&t=16716 |
Page 1 of 1 |
Author: | KKDdaddy [ Tue Feb 25, 2014 1:30 pm ] |
Post subject: | Heim joint tie rods |
I'm looking to swap out my worn out tie rod ends with Heim joints. What size is everyone running? I've found a few kits that are built to length that'll cost not much more than replacing all my tie rods. Thanks for the help in advance. |
Author: | Odyknuck [ Tue Feb 25, 2014 1:36 pm ] |
Post subject: | Re: Heim joint tie rods |
5/8" and 3/4" |
Author: | Jeremy1 [ Tue Feb 25, 2014 5:59 pm ] |
Post subject: | Re: Heim joint tie rods |
I have had good luck with 5/8 heim and miss alignment spacers that step the bolts down to 7/16. I bought some air craft hex aluminum from mc master Carr and cut and drilled and taped them myself. I used all right hand thread so I only need to carry one spare. But I had that set up for the last five years and never needed it. |
Author: | bigDsmith [ Tue Feb 25, 2014 8:21 pm ] |
Post subject: | Re: Heim joint tie rods |
I'm running 5/8" Sent from my Galaxy S3 using TapaTalk |
Author: | bluebuggy [ Tue Feb 25, 2014 10:51 pm ] |
Post subject: | Re: Heim joint tie rods |
I too run 5/8 with 1/2 miss alignment Sent from my SAMSUNG-SGH-I727 using Tapatalk |
Author: | Dee Ell [ Tue Mar 18, 2014 5:37 pm ] |
Post subject: | Re: Heim joint tie rods |
Speedway motors. You can't hardly beat there prices. |
Author: | KKDdaddy [ Thu Mar 20, 2014 10:47 am ] |
Post subject: | Re: Heim joint tie rods |
Dee Ell wrote: Speedway motors. You can't hardly beat there prices. Yeah that's where I was looking at. They have the whole rod and end set up in many different lengths. Sent from my iPhone using Tapatalk |
Author: | bigDsmith [ Thu Mar 20, 2014 10:48 am ] |
Post subject: | Re: Heim joint tie rods |
X2. That's were my setup came from. Sent from my Galaxy S3 using TapaTalk |
Author: | NRIbuggys [ Thu Mar 20, 2014 11:19 am ] |
Post subject: | Re: Heim joint tie rods |
18in long alum hex with 3/4 himes with shims to use a 5/8 bolt Sent from my iPhone using Tapatalk |
Author: | newbie26 [ Thu Mar 20, 2014 5:03 pm ] |
Post subject: | Re: Heim joint tie rods |
Where did u get the aluminum hex Sent from my DROID RAZR using Tapatalk |
Author: | NRIbuggys [ Thu Mar 20, 2014 5:55 pm ] |
Post subject: | Re: Heim joint tie rods |
Race shop next to my house. They use them for 4link bars on dirt cars so speedway prolly has them Sent from my iPhone using Tapatalk |
Author: | nate3923 [ Sun Jul 27, 2014 4:51 pm ] |
Post subject: | Re: Heim joint tie rods |
What size tires are you guys running with the 5/8 hiem joints |
Author: | bigDsmith [ Sun Jul 27, 2014 6:39 pm ] |
Post subject: | Re: Heim joint tie rods |
29x8.5 swampers |
Author: | helmetguy [ Sun Jul 27, 2014 7:46 pm ] |
Post subject: | Re: Heim joint tie rods |
We run 3/4 heims with mis alignment adspters to 1/2 bolt. .they tough ass hell!!!! |
Author: | nate3923 [ Wed Jul 30, 2014 9:00 am ] |
Post subject: | Re: Heim joint tie rods |
Nribuggys where did you get the shimes. I had to make my 5/8 to 1/2 |
Author: | nate3923 [ Wed Jul 30, 2014 9:04 am ] |
Post subject: | Re: Heim joint tie rods |
Nribuggys where did you get the shimes. I had to make my 5/8 to 1/2 |
Author: | nate3923 [ Wed Jul 30, 2014 9:05 am ] |
Post subject: | Re: Heim joint tie rods |
Nribuggys where did you get the shimes. I had to make my 5/8 to 1/2 |
Author: | tw9294 [ Wed Jul 30, 2014 9:59 am ] |
Post subject: | Re: Heim joint tie rods |
bluebuggy wrote: I too run 5/8 with 1/2 miss alignment Sent from my SAMSUNG-SGH-I727 using Tapatalk Same here. |
Author: | Cush53 [ Wed Jul 30, 2014 12:33 pm ] |
Post subject: | Re: Heim joint tie rods |
I think summit has the 5/8 to 1/2 and I run 3/4 to 1/2 works great. I believe the proper name is high misalignment spacers. Gotta have two per heim. The reason I didn't go with the 5/8 to 1/2 is there isn't a lot of material in the spacer wall going from 5/8 to 1/2 so the spacers are kinda weak and could collapse if over tightened |
Author: | NRIbuggys [ Wed Jul 30, 2014 1:14 pm ] |
Post subject: | Re: Heim joint tie rods |
They sell them at the race shop by my house. I'm think they come from speedway. He gets a lot of parts from them Sent from my iPhone using Tapatalk |
Author: | nate3923 [ Wed Jul 30, 2014 4:15 pm ] |
Post subject: | Re: Heim joint tie rods |
I just went with the same set up as nribuggy found a race shop by my house |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |